Commercial and production ÁLAVA
comercial@braseli.com

Administration A CORUÑA
administracion@braseli.com

Export GRANADA
comercial@ferrosystems.com

fn-din-reg pmen">COMPANY fn-din-reg pmen">GROUP GPF fn-din-reg pmen">QUALITY AND SUSTAINABILITY fn-din-reg pmen">PRODUCTS fn-din-reg pmen">DOWNLOADS fn-din-reg mr50 pmen">CONTACT

Tariffs

Braseli TARIFF 2024

Download PDF

GPF GAS TARIFF 2026

Download PDF

Our products

Multilayer
Pipes

PE-X
Pipes

GPF MULT
System

GPF PPSU
System

GPF TERM
System

GPF PRESS
System

GPF AXIAL
System

Tools

Radiator
Valves

Manifold
System

Underfloor
Heating System

GPF GAS
System

Geothermal
Systems

MULTILAYER PIPES

Braseli multilayer pipes are manufactured according to standard EN ISO 21003 "Multilayer piping systems for hot and cold water installations inside buildings" and they have AENOR System Certificates with Braseli metallic press fit fittings and plastic press fit fittings.

RT is a polyethylene that is resistant to temperature. In multilayer pipes a layer of aluminium and an outer polymer adhere to the inner pipe (PE-RT) with the main objective of obtaining pipes that dilate less and are therefore suitable for being used in open or exposed installations.

Product Catalogue MULTILAYER PIPES

Download PDF

FEATURES BRASELI MULTILAYER PIPES

  • They withstand temperatures of 90°C.
  • They withstand high pressures: 10 bar continuous pressure at 70°C for 50 years.
  • Low thermal expansion coefficient, combining the advantages of metallic and thermoplastic pipes.
  • They can be curved manually and regain their original shape as many times as desired, remaining stable in the form generated, which speeds up assembly and allows for open or exposed installations.
  • Impact resistance.
  • They are impermeable to oxygen diffusion and are not affected by ultraviolet rays.
  • Resistance to corrosion, abrasion and to the attack of chemical products.
  • They guarantee low acoustic transmission and high absorption against water hammer.
  • They do not conduct electricity.
  • Minimum head loss.
  • No build-ups or adherences are produced, therefore neither the interior diameter is reduced, nor does roughness increase over time.
  • Sanitary quality: they do not alter the smell or taste of potable water.
  • They resist all actions applied in the prevention and control of legionnaire’s disease.
  • Their lightness makes them easy to transport, stock and install.
  • Their low thermal conductivity coefficient coefficient reduces condensation and heat loss.

CROSSLINKED POLYETHYLENE (PE-Xa and PE-Xb) PIPES

Braseli crosslinked polyethylene (PE-X and PE-Xb) pipes are manufactured according to standard EN ISO 15875: "Plastic piping systems for hot and cold water installations. Crosslinked polyethylene (PE-X)" and they have AENOR System Certificates with Braseli metallic press fit fittings, plastic press fit fittings, metallic sliding sleeve fittings and with plastic expansion sleeve fittings. Braseli’s PE-X System with metallic sliding sleeve fittings also has the QB certificate.

Product Catalogue PE-X PIPES

Download PDF

FEATURES BRASELI PE-X PIPES

  • Manufactured with polyethylene of the highest quality, reticulated by the peroxide method (PE-Xa) or the silane method (PE-Xb), which provides a high degree of cross-linking.
  • They withstand high temperatures, usual working temperatures of 90°C.
  • Resistance to high pressures.
  • They are not affected by corrosion or erosion.
  • High flexibility and resistance to low temperatures: allows the pipe to expand and return to its original size, maintaining watertightness.
  • High resistance to chemical products, even at high temperatures.
  • Minimum head loss, due to their low friction coefficient.
  • No build-ups or adherences are produced, therefore neither the interior diameter is reduced, nor does roughness increase over time.
  • They do not conduct electricity.
  • They reduce water hammer.
  • Sanitary quality: they do not alter the smell or taste of potable water.
  • They resist all actions applied in the prevention and control of legionnaire’s disease.
  • Their lightness makes them easy to transport, stock and install.
  • They do not transmit noises produced by water.
  • Plastic memory: pipes regain their original shape with time or by applying hot air.
  • Their low thermal conductivity coefficient greatly reduces the possibility of water freezing inside, but if freezing did occur, the pipe would dilate and not burst.
  • They are affected by ultraviolet rays and must therefore be protected against sunlight in outdoor installations.
  • 50 years useful life.

Temperature Resistant Polyethylene (PE-RT) Pipes

Braseli temperature-resistant polyethylene (PE-RT) pipes are manufactured according to standard EN ISO 22391 "Plastic piping systems for hot and cold water installations. Temperature-resistant polyethylene (PE-RT)" and they have AENOR Quality Certificate as well as QB Quality Certificate..

PE-RT pipes, due to their molecular structure, do not need to be subjected to a cross-linking process in order to obtain a high resistance to pressure and temperature. They have very similar characteristics to those of PE-X pipes, with a high degree of flexibility. They can be installed with the same type of press fit and sliding sleeve fittings than Braseli crosslinked polyethylene (PE-X) pipes, or welded connections can be carried out.

Anti-Oxygen Barrier EVOH Pipes

Pipes with an anti-oxygen barrier layer are recommended by standard EN 1264 "Underfloor heating. Systems and components". Due to the permeability of crosslinked polyethylene or temperature-resistant polyethylene pipes to oxygen molecules, there is the possibility that the water circulating inside the circuits could receive oxygen from the air which may cause greater corrosion of the metal components in the installation.

Crosslinked polyethylene (PE-X) and temperature-resistant polyethylene (PE-RT) pipes with anti-oxygen barrier EVOH have a layer adhered to them which reduces the oxygen permeability of the pipes to a minimum. Braseli PE-X and PE-RT pipes with EVOH layer are certified by AENOR according to their corresponding standards EN ISO 15875 and EN ISO 22391 and also have QB Quality Certificate.

METALLIC PRESS FITTING SYSTEM FOR MULTILAYER PIPES

Braseli metallic press fitting system for multilayer pipes is manufactured according to standard EN ISO 21003 and has AENOR Quality Certificate.

Product Catalogue GPF MULT Syst.

Download PDF

FEATURES METALLIC PRESS FITTING SYSTEM FOR MULTILAYER PIPES

  • The system combines installation convenience and speed with maximum safety.
  • Two sealing joints increase the guarantee of watertightness.
  • Assembly is carried out in a reliable, quick and clean manner.
  • The stainless-steel sleeve remains in its position by means of a plastic ring, preventing its loss and any damage to the sealing joints before assembly.
  • The generation of galvanic couple is prevented.
  • Pressure tests can be carried out with no waiting time.

PRESSFITTING SYSTEM FOR MULTILAYER AND
PE-X PIPES

Braseli PPSU press fitting system for multilayer and crosslinked (PE-X) pipes is manufactured according to standards EN ISO 21003 for multilayer and EN ISO 15875 for PE-X and has AENOR Quality Certificates with both types of pipes.

Product Catalogue GPF PPSU Syst

Download PDF

FEATURES PPSU PRESS FITTING SYSTEM FOR MULTILAYER AND PE-X PIPES

  • The system is manufactured polyphenylsulfone (PPSU) and brass depending on the type of fitting and its needs.
  • PPSU is characterised by being a plastic material with high thermal stability, great mechanical resistance and a low level of roughness.
  • The interior design of the fittings together with the material used help to reduce occasional head loss and make it difficult for build-ups or adherences to form.
  • Allows for the difference in thicknesses that exists between multilayer and PE-X in certain series.
  • Improves stock management.
  • The sealing joints serve as an additional safety element
  • Assembly is convenient and quick.
  • The stainless-steel sleeve remains in its position.
  • The generation of galvanic couple is prevented through the anticorrosion joint.
  • Pressure tests can be carried out with no waiting time.

PLASTIC EXPANSION RING FITTINGS SYSTEM FOR PE-Xa PIPES

Braseli plastic expansion sleeve fittings system for crosslinked polyethylene (PE-X) pipes is manufactured according to standard EN ISO 15875 and has AENOR Quality Certificate.

Product Catalogue GPF TERM Syst.

Download PDF

FEATURES PLASTIC EXPANSION RING FITTINGS SYSTEM FOR PE-Xa PIPES

  • The system combines installation convenience and speed.
  • Pipe handling is avoided, increasing safety when carrying out the connection.
  • Total watertightness is achieved, without the need for O-rings or bi-cones that could suffer from aging.
  • Assembly is carried out in a reliable, quick and clean manner.

METALLIC PRESS FITTING SYSTEM FOR PE-X PIPES

Braseli metallic press fitting system for crosslinked polyethylene (PE-X) pipes is manufactured according to standard EN ISO 15875 and has AENOR Quality Certificate

Product Catalogue GPF PRESS Syst.

Download PDF

FEATURES METALLIC PRESS FITTING SYSTEM FOR PE-X PIPES

  • The system is characterised by its speed and convenience.
  • Pipe handling is avoided, increasing safety when carrying out the connection.
  • Fittings can be reused.
  • Total watertightness is achieved, without the need for O-rings or bi-cones that could suffer from aging.
  • Pressure tests can be carried out with no waiting time.

METALLIC SLIDING SLEEVE SYSTEM FOR PE-X PIPES

Braseli metallic sliding sleeve system for crosslinked polyethylene (PE-X) pipes is manufactured according to standard EN ISO 15875 and has AENOR Quality Certificate as well as QB Quality Certificate.

Product Catalogue GPF AXIAL Syst.

Download PDF

FEATURES METALLIC SLIDING SLEEVE SYSTEM FOR PE-X PIPES

  • The system is characterised by its safety and reliability.
  • The union offers tensile strength.
  • Assembly is fast and clean.
  • Fittings can be reused.
  • Total watertightness is achieved, without the need for O-rings or bi-cones that could suffer from aging.
  • Allows for fitting rotation once assembled with no loss of watertightness.
  • They hardly reduce the flow rate, and the increase they create on the exterior diameter of the pipe is minimal.
  • Pressure tests can be carried out with no waiting time.

TOOLS

Braseli offers a wide range of tools which are suitable for all its systems.

Product Catalogue TOOLS

Download PDF

ICMA-BRASELI VALVES AND RADIATOR ACCESSORIES

Braseli thermostatic and manual valves for radiator heating installations offer competitive, high-quality solutions for the client.

Product Catalogue VALVES & RADIATOR ACC.

Download PDF

Thermostatic radiator valves

Thermostatic valves are used to regulate and cut-off the flow of the heat-transfer fluid that circulates inside the terminals of the radiator system. Thermostatic control devices are used in combination with thermostatic valves to automatically regulate, keeping the temperature at a pre-established value.

Braseli thermostatic heads can be installed in all of the Braseli thermostatic valves in order to turn heating systems with a manual operating mode into ones with an automatic operating mode. To install the thermostatic head, simply replace the control of the thermostatic valve with the thermostatic head.

The valves are available in straight and square versions. Braseli standard thread valves are designed for connection to copper pipes, crosslinked polyethylene pipes and multilayer pipes.

The valves are also equipped with an airtight elastic joint. This enables the valve to connect to the radiator easily and safely, without needing to use a sealant.

INSTALLATION SYSTEM WITH MANIFOLDS FOR PE-X AND MULTILAYER PIPES

Braseli crosslinked polyethylene systems make it possible to carry out installations with manifolds for plumbing, heating via radiators, industry...

Product Catalogue MANIFOLDS

Download PDF
  • This installation system, by going directly to each element separately from the manifold, guarantees a regular supply to each point of demand, or a uniform distribution of flow and temperature in each radiator.
  • The absence of joints reduces noise and head loss.
  • Failure in a circuit does not affect the whole system.
  • If the pipes are preinsulated, the system allows pipes to be exchanged without the need for specialised labour.

UNDERFLOOR HEATING AND COOLING SYSTEM

Pipes with anti-oxygen barrier are recommended in order to reduce the problems concerning corrosion when plastic pipes are combined with corrosive materials in heating installations.

The pipes are attached, forming circuits which cover the whole surface of the premises to be heated, onto some form of insulation that minimises heat loss towards the lower part of the frame. Another important element for guaranteeing comfort is the control and regulation system.

Underfloor heating is a heating system which involves a circuit of pipes embedded into the mortar located under the flooring through which water of a medium temperature circulates, around 40°C, transmitting, basically through radiation, heat into the room.

For underfloor heating systems, the characteristics and requirements can be found in the standard EN 1264 "Underfloor heating. Systems and components".

Braseli PE-X and PE-RT pipes with EVOH anti-oxygen barrier have a layer adhered to them which reduces the oxygen permeability of the pipes to a minimum. In Braseli multilayer pipes, the layer of aluminium serves this function.

Product Catalogue UNDERFLOOR HEATING

Download PDF

ADVANTAGES BRASELI UNDERFLOOR HEATING

  • Greater comfort, due to the stratification of the temperature in height, as greater comfort is achieved when the temperature of the feet is a little higher than that of the head.
  • Uniform distribution of temperature across the whole floor surface, which also provides a more comfortable environment.
  • Energy savings, given that the heating supply is concentrated to where it is felt by the user, the rising speed of the hot air layers to elevated areas is much lower. There are also considerable savings due to the low flow temperature (45°C) and the lower thermal gap between flow and return (5-8°C).
  • Working with a low temperature makes it possible to use alternative energy sources.
  • It has a nicer aesthetic, given that it is an invisible installation, without elements attached to the wall that make decoration options more difficult, accumulate dirt and which require maintenance or replacement over time.
  • Healthy environment, the fact that it does not cause significant convection currents means that it neither moves dust around the room nor causes the relative humidity to fall.
  • It incorporates thermo-acoustic insulation, which improves the quality and comfort in the building.

MULTILAYER GAS SYSTEM

The GPF GAS Multilayer System for Gas distributed in Spain is the result of the experience of several years manufacturing the product for this application in different countries in which regulations already allowed for it.

Pipes are made up three layers, two made from plastic material and an intermediate layer made from aluminium. The layers are joined using a special adhesive which binds them together and provides:

  • Greater malleability in its manipulation and stability during assembly.
  • Greater mechanical resistance.
  • Greater resistance to gas components.
  • Greater resistance to the odorant impermeability.

GPF GAS PE-AL-PE multilayer gas pipes are manufactured according to standard UNE 53008, which is the only one provided for in the Spanish gas standard.

The jointing system for GPF GAS multilayer pipes combines comfort and speed of installation with safety. Two NBR o-rings increase the safety guarantee.

Product Catalogue GPF GAS Syst.

Download PDF

FEATURES MULTILAYER GAS SYSTEM

  • Total impermeability to gas diffusion.
  • All of GPF GAS pipes and fittings are manufactured in the European Union.
  • Long life.
  • Resistance to corrosion, abrasion and to the attack of chemical products.
  • They are not affected by ultraviolet rays and they allow for outdoor installations.
  • No build-ups or adherences are produced.
  • Minimum head loss.
  • Resistance to high pressures.
  • Reliable and competitive solution, with high price stability.
  • Pipes can be curved manually and regain their original shape as many times as desired.
  • Low thermal expansion coefficient, allows for open or exposed installations.
  • Their lightness makes them easy to transport, stock and install.
  • Assembly is carried out in a reliable, quick and clean manner.
  • Impact resistance.
  • They do not conduct electricity.

GEOTHERMAL SYSTEMS

Braseli markets its Geothermal Environmental Technology as well as the FRANK GET German manufacturing system, which allows for the heating and cooling of buildings thanks to a vast range of innovating solutions for the extraction of geothermal energy through probes and heat pumps.

A large variety of manholes, manifolds and all the components that are part of a modular system designed for the distribution of heat obtained from the natural environment are also provided: pipes, fittings, valves and welding technology.

Product Catalogue Geothermal Systems

Download PDF

ADVANTAGES GEOTHERMAL SYSTEMS

  • Efficient use of an inexhaustible, renewable and fully available energy, with no influence of climatic conditions.
  • Ecological, clean and safe system, without polluting emissions or waste generation.
  • Energy and maintenance cost savings.
  • Amortisation of the initial investment costs.
  • Complete climate control system and energy efficiency: heating, cooling and sanitary hot water.
  • Compatibility with other sources of energy.
  • Aesthetics.
  • Energy mix: reduction of fossil fuel consumption and of the dependence on energy imports.
  • Social: opportunities for new industries and employment creation.
  • CTE: meets the energy savings requirements specified in the Technical Building Code.
  • Public administrations’ support.
  • Longer useful life than other systems.

COMMERCIAL AND PRODUCTION

ÁLAVA

Tel.: +34 902 602 828 / 945 333 050

Fax.: +34 902 602 828 / 945 333 048

Poliígono Industrial de Lantarón

c/ Omecillo, s/n

01213 - Lantarón (Álava)

Spain

comercial@braseli.com

ADMINISTRATION

A CORUÑA

Tel.: +34 981 900 900

Fax.: +34 981 900 901

Paseo Marítimo Alcde. Fco. Vázquez, 63

Plaza Interior

15002 - A Coruña

Spain

administracion@braseli.com

EXPORT

GRANADA

Tel.: +34 981 010 060

Fax.: +34 981 010 061

Ctra. Atarfe a Sta. Fe, s/n

18230 - Atarfe (Granada)

Spain

comercial@ferrosystems.com

www.ferrosystems.com

Legal Notice, Privacy Policy and Cookies